Skip to main content

GTI Industrial Dryers

Short answer: Dryer exhaust condensation is a common cause of wet powder in ducts, damp or blinded filter bags, rust streaks on cyclones and dripping from the stack. The mechanism is simple: some surface in the exhaust path is colder than the dew point of the dryer’s exhaust air. The fix starts with numbers. Calculate the exhaust dew point for your worst operating case (wettest feed, most humid weather, lowest airflow), measure the coldest surface temperatures along the duct, cyclone, filter and fan, and keep every surface safely above that dew point with insulation, heat tracing, leak sealing and correct start-up and shutdown. If the fuel contains sulphur, the acid dew point, not the water dew point, sets the limit.

This guide is for maintenance engineers, production managers and plant consultants dealing with condensation, sticky deposits, bag blinding or corrosion downstream of spray dryers, fluid bed dryers, flash dryers, rotary dryers and belt dryers.

Symptoms that point to exhaust condensation

SymptomWhere it showsWhat is happening
Wet or pasty powder build-upDuct bends, low points, cyclone coneWater condenses on a cold wall and wets the fines that touch it
Rising filter pressure drop, bags hard to cleanBag filterMoist dust blinds the fabric; pulse cleaning cannot release it
Rust, pitting, flaking paintMild steel ducts, hopper walls, fan casingRepeated wetting; worse if acid gases are present
Lumps in recovered finesCyclone or filter dischargeFines picked up moisture before collection
Condensate dripping from stack or flangesStack, expansion jointsExhaust cooled below dew point on the way out
Problems mainly at start-up or in the monsoonWhole exhaust trainCold metal at start-up, or higher ambient humidity raising the dew point

The US EPA’s guidance on monitoring fabric filters notes that lower temperatures allow acid gases to condense and corrode the casing and metal parts, and that condensation can cause bag blinding, which blocks air flow through the bag.

Why dryer exhaust condensation happens even when the gas is hot

Exhaust leaving a dryer at 70–90°C can have a low relative humidity and still carry a lot of water. What matters for condensation is the dew point: the temperature at which that water vapour starts to condense. It depends on the amount of water vapour per kilogram of dry air (the humidity ratio), not on the gas temperature. Any surface colder than the dew point will collect liquid water, even if the bulk gas is much hotter.

Four things raise the exhaust dew point:

  • More evaporation per kg of air. Running at high capacity with reduced airflow, or feeding a wetter product, loads more water into each kilogram of air.
  • Humid ambient air. In humid weather the intake air already carries more water before the dryer adds any.
  • Direct firing. Burning fuel in the drying air adds combustion water vapour. For example, burning methane produces about 2.25 kg of water for every kg of methane burned (from CH₄ + 2O₂ → CO₂ + 2H₂O). An indirectly heated dryer (steam coils, thermic fluid or a heat exchanger) does not add this water.
  • Exhaust recirculation. Recycling part of the exhaust to save energy raises the humidity of the drying air. It is a good energy measure, but it narrows the margin to condensation.

Worked example: calculating the exhaust dew point

Illustrative example only. Use your own measured or design figures. A convective dryer evaporates 500 kg of water per hour into 20,000 kg per hour of dry air.

  • Added moisture = 500 ÷ 20,000 = 0.025 kg water per kg dry air
  • Humid season intake at 32°C and 66% relative humidity: humidity ratio ≈ 0.020 kg/kg, so the exhaust humidity ratio ≈ 0.045 kg/kg
  • Dry season intake at 25°C and 40% relative humidity: humidity ratio ≈ 0.008 kg/kg, so the exhaust humidity ratio ≈ 0.033 kg/kg

At atmospheric pressure, the vapour pressure is p = W × P ÷ (0.622 + W), where W is the humidity ratio and P the total pressure. The dew point is the temperature at which water’s saturation pressure equals p. Using saturation data for water (for example the NIST Chemistry WebBook), this gives:

CaseExhaust humidity ratio (kg/kg dry air)Approximate dew point
Dry season0.033about 33°C
Humid season0.045about 39°C

At 80°C, the humid-season exhaust has a relative humidity of only about 14%, which looks dry, yet any surface below about 39°C will run wet. A 5 kg/h steam leak into the duct, a bypass damper letting in cold air, or a night-time drop in duct wall temperature can push part of the system across that line. In a direct-fired dryer, add the combustion water before calculating.

Where condensation forms, and why

  • Long uninsulated ducts and stacks. Wall temperature falls well below gas temperature where wind and rain cool the outside, especially at low gas velocity.
  • Cyclone cones and hoppers. Large surface area, slow-moving gas and dead zones.
  • Bag filter housings, hoppers and tube sheets. Exposed steel panels and hopper corners. The EPA Air Pollution Control Cost Manual chapter on baghouses states that the gas temperature must remain above the dew point of any condensables, and that the baghouse and associated ductwork should be insulated and possibly heated if condensation may occur.
  • Air leaks. Inspection doors, rotary valves, flanges and expansion joints pull in cold, sometimes humid, air. The leak cools the gas locally and creates a cold spot.
  • Fan casings and dampers. Thin metal and frequent air leakage.
  • Start-up and shutdown. Humid gas meeting cold metal is the most common single cause of intermittent problems.

How to diagnose it step by step

  1. Establish the worst case. Collect feed rate and moisture, airflow, inlet and outlet temperatures, ambient conditions and fuel type for your highest-load, most humid operating case.
  2. Calculate the exhaust dew point. Use a psychrometric calculation as shown above, or measure exhaust humidity directly with a suitable heated probe.
  3. Map surface temperatures. Use a contact thermometer or thermal camera along the duct, cyclone, filter housing, hoppers, fan and stack, preferably during cold, humid weather and during start-up.
  4. Compare. Any surface close to or below the dew point is a likely condensation site. Check those locations for deposits and corrosion.
  5. Check for air ingress. Measure oxygen or temperature on either side of suspected leaks, or look for local temperature drops.
  6. Check the fuel. If you burn furnace oil, coal or some biomass fuels in a direct-fired heater, find out the sulphur content and whether the exhaust contains acid gases.

Fixes that work

Keep surfaces above the dew point

  • Insulate and clad ducts, cyclones, filter housings and hoppers. The EPA cost manual bases its baghouse insulation costs on 3 inches of glass fibre in a metal skin. A US Department of Energy and Argonne handbook on spray-dryer flue-gas cleaning warns that insulation thicknesses below three inches may leave wall temperatures within 10°F of the dew point and recommends at least four inches in that application, with hopper areas insulated too. Your insulation thickness should be calculated for your gas temperature, dew point and climate.
  • Add steam or electric heat tracing on hoppers, cones and dead zones where insulation alone is not enough.
  • Raise the exhaust temperature or airflow only if the product and energy balance allow. More air lowers the humidity ratio; a higher outlet temperature increases the margin. Both cost energy, so check them against your dryer energy audit.

Choose an adequate margin

There is no universal margin. In the flue-gas cleaning application, the DOE/Argonne handbook describes gas leaving the absorber/dryer kept about 20–30°F (about 11–17°C) above its dew point when a fabric filter is used. Use such figures as orientation only and set your own margin with your equipment designer, based on the coldest surface rather than the bulk gas temperature.

Stop cold air ingress

Repair door gaskets, rotary valve clearances, flange gaskets and expansion joints. Leaks also add load to the fan and can upset the dryer’s pressure balance.

Start up and shut down dry

Warm the dryer, ducts, cyclone and filter with hot air before introducing wet feed. At shutdown, stop the feed first and purge with hot, dry air before stopping the fans. Write these steps into the operating procedure and train every shift.

Design for the remaining risk

  • Fit drains at duct low points.
  • Use stainless steel or suitable coatings in zones that will see occasional wetting.
  • Choose filter media for the moisture and temperature conditions; discuss hydrophobic or coated media with the filter supplier.
  • Fit temperature sensors and alarms at known cold spots.

When acids are involved

When fuel contains sulphur, sulphur oxides can form acids that condense at temperatures well above the water dew point. The DOE/Argonne handbook notes that this condensate is an aqueous solution of sulphuric and sulphurous acids that can corrode metal components and damage fabric filter bags. Indirect heating with a clean heat exchanger, or switching to a low-sulphur fuel, removes this problem at the source. Our guide to choosing the dryer heat source covers the trade-offs.

Related problems that look similar

Not every sticky deposit is condensation. In spray dryers, powder can stick because the product itself becomes sticky at the outlet conditions. See why spray dryers produce sticky powder or wall deposits. Hygroscopic powders can also absorb moisture from humid exhaust air without any liquid water forming, then cake later in storage. See powder caking after drying. Wet combustible deposits in ducts and filters are also a fire risk. Our dryer fire and dust explosion checklist covers that side.

Checklist for engineers

  • Worst-case exhaust dew point calculated, including combustion water and recirculation
  • Surface temperature survey done in cold, humid conditions and at start-up
  • Insulation and cladding intact on ducts, cyclones, filter housings and hoppers
  • Heat tracing on hoppers and dead zones where needed
  • Air leaks at doors, valves, flanges and expansion joints repaired
  • Start-up preheat and shutdown purge written into procedures
  • Drains at duct low points, and materials suited to occasional wetting
  • Fuel sulphur content known; acid dew point considered if relevant
  • Temperature alarms at known cold spots

Frequently asked questions

Why do I get condensation when the exhaust is at 80°C?

Because condensation depends on the dew point, not the gas temperature. Exhaust at 80°C can have a dew point near 40°C. Any duct or hopper wall below that temperature will collect water.

Does a direct-fired dryer have more condensation risk than a steam-heated one?

For the same evaporation and airflow, yes, because combustion adds water vapour to the drying air. It also adds acid-gas risk if the fuel contains sulphur.

Will exhaust air recirculation cause condensation?

It raises the humidity of the air in the dryer and exhaust, which raises the dew point. It can still be used safely if surfaces are kept above the new dew point.

Is insulation alone enough?

Often, but not always. Hoppers, dead zones, start-up periods and air leaks may also need heat tracing, procedural changes or repairs.

Get help with dryer exhaust problems

For assistance with exhaust condensation, dryer selection, processing requirements or a project-specific quotation, contact Genex Tech Industries LLP (GTI Group). GTI supplies industrial spray dryers, vibratory fluidised bed dryers and rotary drum dryers with their air handling and dust collection systems.

Email: mktg@gtidryers.com
Call or WhatsApp: +91-93300 77417
Website: https://gtidryers.com/

Please share your material, required wet-feed capacity, initial and target moisture, available heating source and installation location.

Chat on WhatsApp