Short answer: When a powder leaves the dryer free-flowing but turns lumpy or solid in bags, bins or silos days or weeks later, the cause is usually one of four things: an amorphous powder has become too warm or too moist for its glass transition temperature; a crystalline powder has been exposed to humidity near its deliquescence point, often in cycles; warm powder was packed before it cooled; or the bulk has been under pressure for too long. The fix starts with a measured specification for moisture or water activity and packing temperature, then works back to the dryer, the cooler and the packing room.
This guide is for production managers, quality teams and process engineers dealing with powder caking after drying in food ingredients, dairy powders, extracts, chemicals, salts and fertilisers. It is about caking that develops in storage. If powder is sticking to the walls inside a spray dryer, see our separate guide to sticky powder and wall deposits in spray dryers. For a broader overview of dryer faults, see common problems in industrial dryers.
How caking develops
Caking is not one event. A 2025 study on caking of amorphous carbohydrate powders describes four stages: bridging between particles, agglomeration, compaction and, at the extreme, liquefaction. A review of bulk powder caking in *Powder Technology* explains the bridges themselves: liquid bridges from condensed moisture, and solid bridges formed when dissolved material recrystallises or when softened particles fuse together.
Which bridges form depends mostly on whether your powder is amorphous or crystalline.
Step 1: Know which kind of powder you have
| Powder type | Typical examples | Main caking mechanism | Key variable to control |
|---|---|---|---|
| Amorphous (glassy) | Spray-dried fruit and vegetable powders, maltodextrin-based products, many dairy and extract powders | Particles soften and fuse when storage temperature rises above the glass transition temperature (Tg), which falls as moisture rises | Water activity or moisture, and storage temperature |
| Crystalline | Salt, sugar, many inorganic chemicals and fertiliser salts | Surface dissolves at high humidity, then recrystallises into solid bridges when humidity falls | Relative humidity exposure and humidity cycles |
| Protein-rich amorphous | Milk protein concentrates, whey protein concentrates and isolates | Protein-mediated particle bonding as well as glass transition effects | Water activity, temperature and storage time |
| Mixtures | Premixes, seasonings, blends | Weakest component often controls; mixtures can deliquesce at lower humidity than either pure component | Formulation and humidity |
Spray drying often produces amorphous material even from ingredients that are crystalline in raw form, because the water leaves too quickly for crystals to form. A recent review of caking in high-protein dairy powders also notes that protein-rich powders behave differently from lactose-rich ones, so treat each grade on its own data.
Step 2: Understand the mechanism for amorphous powders
Amorphous powders behave like a glass below their glass transition temperature: rigid and free-flowing. Above it they become rubbery, particles soften at contact points and bridges form. Water acts as a plasticiser and lowers Tg, so a powder that is stable when dry can cake at the same temperature once it picks up moisture.
The 2025 study cited above confirms that the degree of caking can be described by the gap between storage temperature and Tg (T − Tg). No caking occurred while the powder stayed glassy. It also tested powders that were warmed in a closed container and cooled again, which is similar to warm powder sealed in a bag. Powders with higher water activity caked in the same way as humidity-exposed samples, while very dry powders resisted caking even after crossing Tg. Water was acting as the binder. In plain terms, temperature and moisture work together. Warm packing of a powder that is already near its moisture limit is a classic route to caking.
Step 3: Understand the mechanism for crystalline powders
Crystalline powders cake mainly through humidity. Each soluble crystal has a deliquescence relative humidity: above it, the crystal surface absorbs water and dissolves. An Annual Reviews article on deliquescence explains that blends of deliquescent ingredients can start to dissolve at lower humidity than either ingredient alone, and that cycles of deliquescence and recrystallisation cause agglomeration and caking.
For sodium chloride, the equilibrium relative humidity over a saturated solution is 75.29% at 25°C, according to the NIST/NBS reference data for saturated salt solutions. Salt held above that humidity picks up water at the surface; when the air dries out again, the dissolved salt recrystallises as bridges between grains. Day-night humidity swings in a warehouse can repeat this cycle many times.
Step 4: Diagnose before you change the dryer
Collect facts before adjusting temperatures:
- Compare caked and free-flowing samples from the same batch for moisture, water activity and, where relevant, particle size.
- Record powder temperature at packing, not just dryer outlet air temperature.
- Log packing room and warehouse temperature and humidity, including night-time values.
- Map where the lumps are. Lumps at the top of bags point to moisture entering from outside or condensation. Lumps at the bottom of tall stacks point to pressure and time. Lumps near bag walls in warm stores point to temperature gradients.
- Note the time to caking. Caking within hours suggests the powder was already above its stability limit when packed. Caking after weeks suggests storage conditions or packaging.
- Check the packaging. Liner integrity, seal quality and the water vapour barrier of the material.
Check that your water activity meter is telling the truth
Water activity readings drive many of these decisions, so verify the instrument. The NIST data gives equilibrium humidities at 25°C of 11.30% for saturated lithium chloride, 32.78% for magnesium chloride and 75.29% for sodium chloride. These correspond to water activities of about 0.113, 0.328 and 0.753. Salt-solution standards of this kind are a common way to check that a water activity meter reads correctly across its range.
Symptom, cause and fix
| What you see | Likely cause | Check | Typical fix |
|---|---|---|---|
| Bags cake within a day or two of packing | Powder packed warm, or moisture or water activity above stable limit | Packing temperature; water activity at packing | Add or improve cooling before packing; tighten final moisture control |
| Caking worse in monsoon or humid months | Moisture pickup during handling or through packaging | Packing room humidity; liner and seal checks | Dehumidified packing area; better barrier packaging |
| Hard layer at the top of bags | Condensation or moisture entry | Temperature history of store; seal integrity | Avoid warm-to-cold transfers; improve sealing |
| Bottom bags in tall stacks cake first | Consolidation under load over time | Stack height; storage duration | Lower stacks; first-in, first-out rotation |
| Crystalline product forms solid lumps after weather changes | Humidity cycling around deliquescence point | Warehouse humidity log | Control storage humidity; conditioning or anticaking measures where permitted |
| Spray-dried powder clumps in warm stores | Storage temperature above Tg at actual moisture | Measure Tg or a sticky point at your moisture | Lower final moisture, cooler storage, formulation review |
Fixes at the dryer and cooler
- Set final moisture on stability data, not habit. For amorphous powders, the right target comes from the relation between water activity and Tg for your product. Over-drying is not always the answer, as it costs energy and can damage some products.
- Cool before packing. A fluid bed cooler or the cooling section of a combined dryer brings powder close to ambient before it is sealed. GTI’s dairy powder drying page describes fluid bed stages for uniform powder cooling and better flowability. For other products, the vibratory fluidised bed dryer and combination dryer pages cover after-drying and conditioning options. The cooling air itself must be dry enough not to add moisture.
- Protect the powder in conveying. Pneumatic conveying with humid ambient air can undo the dryer’s work for hygroscopic products.
- Consider a crystallisation or conditioning step where the chemistry calls for it, for example products that contain amorphous sugars which later crystallise in the bag.
For spray-dried products, outlet temperature, inlet temperature and atomisation all affect final moisture and particle structure. GTI’s industrial spray dryers are designed product by product, and stability targets should be part of that design brief. For salts and similar crystalline products, GTI’s salt drying systems page covers the drying side. Food Tech Projects supplies complete salt processing lines where caking control extends into refining and packing.
Fixes in packing and storage
- Pack in a controlled area, and keep the powder sealed between dryer and packing machine.
- Choose packaging by its water vapour barrier, not just strength. Check liner seals routinely.
- Keep warehouse temperature and humidity steady. Avoid moving powder from hot areas into cooler, humid ones.
- Limit stack height and storage time for products known to consolidate.
- Any anticaking agent must be permitted for the product and its market under the applicable food or product regulations.
When the dryer itself needs to change
Most storage caking is solved by moisture control, cooling and packing discipline. A process change is worth studying when the existing dryer cannot reach the required moisture without damaging the product, has no practical way to add a cooling stage, or delivers widely varying moisture because of poor air distribution. In those cases, test samples under controlled storage conditions before deciding. Our article on pilot plant testing for industrial dryers explains how trials reduce that risk.
Frequently asked questions
Why does my powder flow well at the dryer but cake in the bag?
The dryer outlet is only a snapshot. Caking needs time, temperature, moisture and pressure. Powder that is slightly too warm or too moist when sealed can cake over the following days.
Is moisture content or water activity the better specification?
Both are useful. Moisture content tells you how much water is present. Water activity tells you how available that water is, which links more directly to caking, microbial growth and Tg. For amorphous powders, water activity is usually the better stability indicator.
Will drying to a lower moisture always stop caking?
Not always. It helps amorphous powders, but crystalline powders can still cake if they meet high humidity later. Over-drying also costs energy and can harm product quality.
Do fluid bed coolers solve caking?
They solve the warm-packing part of the problem. They do not fix high moisture, poor packaging or humid storage.
Talk to GTI about powder stability
For assistance with dryer and cooler selection to control caking, processing requirements or a project-specific quotation, contact Genex Tech Industries LLP (GTI Group).
Email: mktg@gtidryers.com
Call or WhatsApp: +91-93300 77417
Website: https://gtidryers.com/
Please share your material, required wet-feed capacity, initial and target moisture, available heating source and installation location.