Skip to main content

GTI Industrial Dryers

Short answer: Uneven final moisture in a band or mesh belt dryer almost always comes from one of four causes:

  • uneven product loading on the belt
  • uneven air distribution through the bed (duct and plenum design, blocked mesh, air bypassing at the belt edges)
  • unstable zone temperature or humidity control
  • variation in the feed itself (piece size, initial moisture)

Locate the problem with a grid of moisture samples across the belt width and along the dryer before changing temperatures. Most plants respond to wet spots by overdrying everything. That wastes heat and saleable weight and can damage colour, but it does not remove the cause.

This guide is for production managers, process engineers and maintenance teams running continuous belt dryers on vegetables, spices, fruit pieces, coconut, feed or other particulate materials.

Why belt dryers develop wet streaks and wet spots

In a through-circulation belt dryer, the product sits still on the belt while air passes through the bed. Unlike a rotary or fluid bed dryer, nothing mixes the product sideways. Any variation across the belt width at the inlet tends to persist to the outlet.

Research on a multi-belt conveyor dryer for medicinal and spice herbs, published in Landtechnik (2009), measured an air temperature drop of about 30 °C from the sides to the middle of the first belt, with correspondingly higher product moisture in the middle. The authors note that the drop at the end of each belt turns the product over but does not mix it across the width. They also note that operators typically overdry to bring wet spots into specification. In that study, guide plates and better flap adjustment in the air supply duct improved air distribution. A later Biosystems Engineering study (2013) applied CFD-based modifications to improve airflow distribution in a multi-belt dryer for spice plants.

The lesson for any plant: before blaming the product or the burner, find out whether the air and the product are evenly spread.

Step 1: Measure the variation properly

A single moisture reading at the discharge chute hides the pattern. Use a sampling grid:

  • Across the width: at least left, centre and right. On wide belts, use five positions.
  • Along the dryer: at the discharge and, where safe access exists, at the end of each zone or tier.
  • Over time: repeat over at least two shifts to separate steady patterns from feed fluctuations.

Record moisture on a consistent basis. Wet basis (% of total mass) is normal for product specifications. Note the test method, because oven, halogen and NIR methods can read differently.

Illustrative example of a discharge grid

PositionSample 1Sample 2Sample 3
Left edge6.2%6.0%6.4%
Centre9.1%8.7%9.3%
Right edge6.5%6.1%6.6%

For these nine readings (wet basis), the mean is 7.2%, the standard deviation is 1.39 percentage points, and the coefficient of variation is about 19%. The range is 3.3 points. The pattern is clear: the edges are dry and the centre is wet. That points to air distribution or bed loading, not overall temperature.

Step 2: Read the pattern

PatternMost likely causesWhat to check
Wet centre, dry edgesAir entering from side plenums does not reach the belt centre; bed thicker in the centre; air bypassing at the edgesAir velocity across the width; bed depth profile; side seals and edge gaps
Wet edges, dry centreProduct piled at the edges by the feeder; edge seals blocking airflow; mesh blinded at the edgesFeeder and spreader setting; mesh condition at the edges
One side wetter than the otherDamper or flap imbalance; fan or duct asymmetry; belt tracking off-centre; feeder discharging to one sideDamper positions; belt tracking; feeder alignment
Wet patches that move or changeLumps and clusters in the feed; intermittent feeding; piece-size variationUpstream cutting and blanching; feed rate stability
Whole product too wet, uniformOverall capacity limit: too much evaporation load, low air temperature, high exhaust humidityFeed rate and moisture; zone temperatures; exhaust humidity and recirculation ratio
Moisture drifts over the dayChanging ambient air, fouling of heat exchangers or mesh, feed moisture swingsTrends of inlet and exhaust conditions; cleaning intervals

Step 3: Measure airflow through the bed

With the dryer running and product on the belt, measure air velocity above the bed at grid points across the width in each zone. Use an anemometer suited to the temperature, and do this only with a safe access arrangement and the plant’s permit procedure. Compare readings, not just averages.

A CFD study of a feed belt dryer in Energy Procedia (2017) showed that bed thickness significantly changes the airflow velocity distribution. Air takes the path of least resistance, so thinner or more open areas of the bed get more air and dry faster.

Common mechanical causes of poor air distribution:

  • Blinded mesh or perforations. Sugar, starch, fat or fines block the openings. Cleaning frequency should match the product.
  • Damaged or missing baffles and guide plates in the plenums.
  • Edge seals and side gaps. Air bypasses along the belt edges instead of passing through the product.
  • Damper positions changed during maintenance and never reset.
  • Fan problems. Slipping belts, a fouled impeller, or a VFD set below design speed.

Step 4: Check bed loading and feed preparation

Even air cannot fix an uneven bed. Check:

  • Bed depth profile across the width at the inlet. Measure it, do not just look at it.
  • Feeder or spreader type and setting. Oscillating spreaders, vibratory feeders and levelling rollers each need adjustment for the product.
  • Piece size consistency. Mixed thick and thin slices dry at different rates even with perfect air. Uniform cutting upstream, for example with a food slicer machine set to a consistent thickness, makes dryer control easier.
  • Surface water. Product carrying wash or blanch water into the dryer adds load unevenly. Dewatering before the dryer helps.

For sticky or very wet feeds that clump, see our guide to handling high initial-moisture feeds without clogging the dryer.

Step 5: Review zone control

In multi-zone dryers, the first zones remove most of the water, and their exhaust is very humid. If zone temperature sensors are badly placed (for example, measuring air before it mixes), the controller may hold the wrong condition. Check:

  • sensor location, calibration and response
  • the recirculation-to-exhaust ratio in each zone: too much recirculation raises humidity and slows drying, while too little wastes heat
  • final-zone conditions, which set the equilibrium moisture the product can reach

Raising temperature to compensate for poor distribution often damages colour and aroma on the already-dry areas. See how to prevent product degradation and colour change during drying.

What overdrying costs: an illustrative calculation

Suppose a line processes 1,000 kg/h of dry solids and the specification is 8% maximum moisture (wet basis). Because the centre runs wet, operators lower the average to 6.5% so that the wettest areas stay within limit.

  • Product at 8.0% average: 1,000 ÷ 0.920 = 1,087 kg/h
  • Product at 6.5% average: 1,000 ÷ 0.935 = 1,070 kg/h

The difference is about 17 kg/h. That is 17 kg/h of extra water evaporated, which costs thermal energy, and 17 kg/h less product sold, which matters for anything sold by weight. Over a 20-hour production day, that is roughly 350 kg of saleable mass. The heat penalty depends on your dryer’s specific heat consumption.

These figures are illustrative. Use your own throughput, specification and prices.

Corrective actions in order of cost

  1. Clean the mesh and plenums, and restore damper settings to the commissioning record.
  2. Repair edge seals and side gaps, and correct belt tracking.
  3. Adjust the feeder or spreader to level the bed; check for uniform piece size upstream.
  4. Recalibrate or relocate zone temperature and humidity sensors.
  5. Fit or adjust air guide plates and flaps. Where justified, carry out an airflow study.
  6. Review whether the dryer is overloaded for the current evaporation duty. If so, discuss capacity, zoning or pre-drying options with the manufacturer.

Preventing the problem in a new dryer specification

When buying a continuous band dryer or a mesh belt dryer, ask the supplier:

  • How is air distributed across the belt width in each zone, and how can it be adjusted?
  • What feeder or spreader is proposed for the product, and how is bed depth controlled?
  • What sampling points and access are provided for moisture and air velocity checks?
  • How are the mesh and plenums cleaned?
  • What moisture uniformity was achieved in trials on the same or a similar product?

GTI’s mesh belt dryer documentation lists airflow distribution and product bed thickness among the critical parameters, alongside belt speed, air temperature and feed moisture. Our article on energy-efficient band dryers with heat recovery covers the energy side.

Frequently asked questions

Is ±1% moisture variation acceptable?

It depends on the product specification and how close the average runs to the limit. Calculate the spread, for example as a standard deviation, and keep the average far enough below the limit that the wettest fraction still complies.

Can I fix uneven drying by slowing the belt?

Slowing the belt increases residence time for all the product. It may bring wet spots into specification, but it overdries the rest and reduces capacity. Find the cause first.

How often should mesh belts be cleaned?

As often as the product requires to keep openings clear. For sugar-rich or fatty products, this can be much more frequent than for dry, non-sticky materials. Monitor air pressure drop or velocity as an indicator.

Should moisture be measured inline?

Inline sensors help track trends. Calibrate them against a reference laboratory method and combine them with periodic grid sampling, because a single sensor sees only part of the belt.

Get help with your belt dryer

For help diagnosing uneven moisture, upgrading an existing band or mesh belt dryer, or a project-specific quotation, contact Genex Tech Industries LLP (GTI Group).

Email: mktg@gtidryers.com
Call or WhatsApp: +91-93300 77417
Website: https://gtidryers.com/

Please share your material, required wet-feed capacity, initial and target moisture, available heating source and installation location.

Chat on WhatsApp