Short answer: The right dryer depends on four things:
- what you feed it (clear juice or fibrous purée)
- whether a carrier such as maltodextrin is allowed on the label
- what powder properties the customer wants (colour, solubility, bulk density, flowability)
- the throughput you need
Spray drying gives fine, free-flowing powders at high throughput, but sugar-rich fruit usually needs a drying aid. Drum drying handles purées and pastes directly and simply, but product temperatures are higher, so colour and flavour suffer more. Refractance window drying dries purée as a thin film at moderate product temperature. In published comparisons it gives colour close to freeze-dried product, but throughput per unit of equipment is lower than spray drying. Trials on your own fruit should make the final decision.
This comparison is for fruit processors, ingredient manufacturers and project consultants deciding how to turn mango, banana, guava, berry, tomato or similar purées and juices into powder.
Why fruit is difficult to dry into powder
Fruit solids are mostly sugars (glucose, fructose, sucrose) and organic acids. Low-molecular-weight sugars and acids have low glass transition temperatures. When the particle temperature during drying is well above the glass transition temperature of the partially dried solids, the material behaves like a sticky syrup rather than a powder. It sticks to dryer walls, cakes in cyclones and forms lumps.
Bhandari, Datta and Howes (1997), “Problems associated with spray drying of sugar-rich foods” is the classic description of this problem. It is why spray-dried fruit powders are commonly made with high-molecular-weight drying aids such as maltodextrin. Those aids raise the glass transition temperature of the mixture.
Every drying method has to deal with this stickiness somehow: by adding a carrier, by drying in a thin film and scraping it off, or by drying at a lower product temperature and cooling the product before it is handled.
What the research shows: one fruit, four methods
Caparino et al. (2012), Journal of Food Engineering dried the same Philippine “Carabao” mango purée by refractance window (RW), freeze drying, drum drying and spray drying (the full text is available from Washington State University). The purée started at 6.52 kg water/kg mango solids and was dried to below 0.05 kg water/kg solids.
| Parameter (from Caparino et al., 2012) | Refractance window | Drum | Spray | Freeze (reference) |
|---|---|---|---|---|
| Residence time | About 180 s | About 54 s | Under 3 s (estimated) | About 31 h |
| Measured product temperature | 74 ± 2 °C | 105 ± 5 °C | 90 ± 2 °C | 20 °C |
| Drying aid | None | None | Maltodextrin DE 10, 0.25 kg/kg mango solids | None |
| Colour vs freeze-dried | Comparable | Darker | Lighter (diluted by maltodextrin) | — |
| Bulk density | Higher (denser, flaky) | Higher (irregular, sharp-edged) | Lower (spherical, porous) | Lower (porous) |
| Hygroscopicity (7 days at 75.5% RH) | 18.0%, same as freeze-dried | 20.1%, highest | 16.5%, lowest | 18.0% |
The study also found no significant difference in glass transition temperature between the four powders, and all were amorphous. The authors conclude that RW produced mango powder comparable to freeze-dried product and better than drum- and spray-dried powders on the quality attributes measured.
Limits of this evidence: it is one fruit, one set of laboratory and pilot-scale conditions, and one carrier level. Industrial results depend on purée solids, fibre content, equipment design and operating settings. Use it as direction, not as a performance guarantee.
How each method works for fruit
Spray drying
The feed must be pumpable and atomisable. Clear juices and concentrates spray well. High-fibre purées may need finishing, dilution or enzymatic treatment so the feed atomises consistently. Drying aids are commonly needed for sugar-rich fruit, and the carrier ratio becomes a recipe and labelling decision. Spray dryers offer the highest throughput per installation. They produce fine powders with controlled particle size and can be integrated with agglomeration for instant powders.
GTI’s industrial spray dryers are designed for pumpable liquids, slurries and emulsions. If wall deposits are a problem, see why spray dryers produce sticky powder or wall deposits.
Drum drying
A thin film of purée is applied to a steam-heated rotating drum and scraped off as a flake or sheet, which is then milled. Drum dryers handle thick purées and pastes without atomisation and without a carrier. Because heat is transferred directly through the drum wall, air volumes are much smaller than in spray drying. The trade-off is a higher product temperature. In the mango study the drum product reached about 105 °C and was darker and more hygroscopic.
GTI’s single and double drum dryers list fruit purées and tomato paste among their applications. Our drum dryer guide explains the design options.
Refractance window drying
Purée is spread as a thin layer on a plastic film floating on circulating hot water. Heat passes through the film into the product. In the Caparino study the water was at 95–97 °C, and the measured product temperature was about 74 °C. RW handles fibrous purées without a carrier. The dried sheet is scraped off, cooled and milled. Throughput per square metre of film is lower than the throughput of a spray dryer of similar footprint, so RW suits premium, clean-label or high-value products where quality and the absence of a carrier justify the capacity cost.
See GTI’s refractance window drying systems and our explainer on what a refractance window dryer is.
Worked example: what a carrier does to your mass balance
Illustrative basis: 1,000 kg/h of mango purée at 6.52 kg water/kg solids (86.7% moisture, wet basis), as in the study above. Target 0.05 kg water/kg solids (4.8% wet basis).
| Item | RW or drum (no carrier) | Spray (maltodextrin 0.25 kg/kg fruit solids, added as dry powder) |
|---|---|---|
| Fruit solids in | 133.0 kg/h | 133.0 kg/h |
| Maltodextrin added | 0 | 33.2 kg/h |
| Total feed | 1,000 kg/h | 1,033 kg/h |
| Powder out at 0.05 kg/kg | 139.6 kg/h | 174.5 kg/h |
| Water evaporated | 860 kg/h | 859 kg/h |
| Fruit share of powder solids | 100% | 80% |
The evaporation load is almost identical. What changes is the product: the spray-dried powder contains 20% carrier on a solids basis. That affects the label, the cost per kg of fruit solids and the colour, which is lighter. With higher carrier ratios the fruit share falls further.
Many spray-drying operations concentrate juice before drying to reduce evaporation, which changes this balance again. RW and drum dryers usually take the purée closer to its natural solids content.
Minimum latent heat for about 860 kg/h of evaporation is roughly 860 × 2,300 kJ/kg ≈ 2.0 GJ/h (about 0.55 MW) in every case. Actual thermal demand differs by technology and design. Ask each supplier for a heat balance, and for electrical power separately.
Side-by-side summary for buyers
| Decision factor | Spray | Drum | Refractance window |
|---|---|---|---|
| Feed form | Juice, concentrate, finished purée | Purée, paste, slurry | Purée, paste, juice concentrate |
| Carrier usually needed for sugar-rich fruit | Yes | No | No |
| Product form | Fine spherical powder | Flakes, milled to powder | Sheet or flakes, milled to powder |
| Thermal exposure | Short time, outlet-air dependent | Short time, high wall temperature | Moderate product temperature, minutes |
| Colour and aroma retention | Good with carrier dilution | Lowest of the three in published mango work | Closest to freeze-dried in published mango work |
| Throughput per installation | Highest | Medium | Lower |
| Air handling and dust | Large air volume, cyclone or bag filter | Small vapour hood | Moderate exhaust |
| Clean label | Depends on carrier | Yes | Yes |
Practical buyer checklist
- Fruit types and varieties, and purée or juice solids (°Brix and total solids).
- Fibre content and whether pulp must stay in the powder.
- Label constraints: is a carrier allowed, and up to what ratio?
- Target moisture or water activity, particle size and bulk density.
- Solubility or reconstitution requirements.
- Throughput in kg/h of feed and of powder, and the seasonal operating window.
- Utilities: steam, hot water and electrical supply.
- Packaging environment. Fruit powders are hygroscopic and need low-humidity handling.
Upstream preparation (washing, pulping, finishing, concentration) is part of the same decision. GTI Group’s fruit and vegetable processing machinery on foodtechprojects.com covers turnkey lines from raw fruit to purée and powder. GTI’s fruit drying systems page describes the dryer options.
Frequently asked questions
Can fruit powder be spray dried without maltodextrin?
Sometimes, with careful formulation, low outlet temperatures, dehumidified air or chamber cooling. However, sugar-rich fruits commonly need a drying aid. Confirm with trials.
Is refractance window drying the same as freeze drying?
No. RW is a continuous thin-film contact drying method at atmospheric pressure. Freeze drying sublimes ice under vacuum. In the cited mango study, RW powder had colour comparable to freeze-dried powder but was denser and less porous.
Why are drum-dried fruit powders darker?
Higher product temperature promotes browning reactions. In the mango study, product temperature on the drum was about 105 °C.
Which method has the lowest operating cost?
It depends on fuel and electricity prices, feed solids, carrier cost and capacity. Compare suppliers’ heat balances and electrical loads on the same basis, and include carrier cost for spray drying.
Discuss your fruit powder project
For help choosing between spray, drum and refractance window drying for your fruit powder, or a project-specific quotation, contact Genex Tech Industries LLP (GTI Group).
Email: mktg@gtidryers.com
Call or WhatsApp: +91-93300 77417
Website: https://gtidryers.com/
Please share your material, required wet-feed capacity, initial and target moisture, available heating source and installation location.