Skip to main content

GTI Industrial Dryers

Short answer: A drum dryer and an agitated thin-film dryer both dry pastes and slurries by conduction through a steam- or oil-heated metal wall, but they handle the film differently. A drum dryer spreads a thin film on the outside of a rotating heated drum and scrapes the dried sheet off with a doctor blade, so it suits pastes, gelatinised starches and purees that are wanted as flakes. An agitated thin-film dryer (ATFD) spreads the feed on the inside of a heated cylinder with a rotor, which keeps renewing the film and suits fouling-prone, heat-sensitive or sludge-like feeds that must be dried into powder in a closed machine. Neither is a universal answer. Solids content, viscosity, fouling tendency, required product form and the need to contain vapours decide the choice, and a trial confirms it.

This comparison is for process engineers, plant managers and consultants who have a feed too thick to spray and too wet to put in a rotary or belt dryer. Genex Tech Industries LLP (GTI Group) offers both machine types, so this article gives the engineering logic rather than a sales claim. Check the published sources below before you rely on any number, and use your own feed in trials.

Stainless-steel food and ingredient processing facility interior (stock photo)
Stock photograph of a food production facility (Pexels, Adrien Olichon). Illustrative only; not a GTI installation or a drying machine.

The two machines in brief

Drum dryer. A TNO review of thin-film drying describes the moist material being applied in a layer of roughly 0.5–2 mm on the outer surface of a heated drum, and notes that atmospheric drum dryers are heated with steam at up to about 200 °C. Product temperatures are typically 120–170 °C on atmospheric machines and 35–60 °C on vacuum drum dryers, and residence time on the drum ranges from a few seconds to dozens of seconds (TNO, Thin Film Drying Processes). Single drums use dip pans, applicator rolls or spray feeds, and double drums feed into the nip between two counter-rotating drums. GTI’s drum dryer page describes single and double drum machines using steam-heated rotating drums with doctor-blade removal.

Agitated thin-film dryer. A peer-reviewed study describes an ATFD as a heated body (stator) with a close-clearance rotor in which the feed passes through slurry, paste, wet powder and finally dry powder, and states that its short residence time, high turbulence and rapid surface renewal let it handle heat-sensitive, viscous and fouling feeds (Chemical Engineering and Processing). The TNO review adds that thin-film dryers suit solutions or suspensions containing typically no more than about 60% solids, produce powder commonly in the 200–600 µm range, and can operate from near vacuum to atmospheric pressure. GTI’s continuous thin-film dryer page describes its agitated thin-film range for viscous, heat-sensitive feeds.

Where each machine fits the feed

An NPTEL course note summarises drum dryers as handling materials too thick for a spray dryer and too thin for a rotary dryer (NPTEL module). The TNO review adds that drum dryers can dry very viscous foods such as pastes and cooked or gelatinised starch that cannot easily be dried by other methods. A Wageningen University publication describes drum drying and refractance window drying as more readily applied to viscous liquid foods, pastes and purees, while ATFD is not yet widely applied in foods (Mild conductive drying of foods).

QuestionDrum dryerAgitated thin-film dryer
How is the film made?Applied on the outside of a rotating drumSpread on the inside of a heated cylinder by a rotor
Film renewalFilm is scraped once per revolutionBlades keep working the film as it dries
Fouling-prone or sticky feedPossible, controlled by film thickness and bladeA design strength according to the literature
Product formFlakes or sheets, usually milled afterwardsPowder or granules directly
Vapour handlingHood over an open drumEnclosed body; can run from near vacuum to atmospheric
Typical feedPastes, purees, gelatinised starch, yeast, extractsViscous, heat-sensitive or fouling feeds, some sludges
Operating pressureAtmospheric, or vacuum drumNear vacuum to atmospheric
Maturity in food useLong establishedLess widely applied in foods

Spray drying is a third option for feeds that can be pumped and atomised. Our atomiser comparison and fruit powder spray versus drum versus refractance window guide cover that boundary. A spray dryer is unlikely to suit very viscous pastes, but it is the usual route for a free-flowing liquid where a fine, free-flowing powder is wanted.

What drives drum dryer performance

For a drum dryer, the film thickness is critical. A diffusion model validated on a pilot-scale twin-drum dryer drying biological sludge identified film thickness as the most critical operating parameter for final moisture and productivity (Drying Technology). A thinner film dries faster, but throughput per drum revolution falls; thicker films raise throughput but risk a wet product. Related controls are steam pressure, drum speed and the nip gap or applicator setting. A single drum is controlled by the gap between blade and drum; a double drum by the nip, and GTI’s page lists moisture control through steam pressure, drum speed and film thickness.

What drives ATFD performance

For an ATFD, the key factors are rotor design, wall temperature, feed rate and the changing state of the material as it passes along the machine. The ScienceDirect study notes the three-phase character (liquid, paste, powder), which makes the flow hard to model and the design a strong function of the process fluid. This is why a trial is more important than a catalogue value.

Illustrative mass balance (not a quotation)

Assume 500 kg/h of paste at 70% wet-basis moisture (30% solids), dried to 5% wet-basis moisture.

  • Dry solids: 500 × 0.30 = 150 kg/h.
  • Dried product: 150 ÷ 0.95 ≈ 157.9 kg/h.
  • Evaporation: 500 − 157.9 ≈ 342.1 kg/h.
  • In dry-basis terms the feed is 0.70 ÷ 0.30 ≈ 2.33 kg/kg, and the product is 0.05 ÷ 0.95 ≈ 0.053 kg/kg.

The TNO review reports steam consumption in atmospheric drum drying of about 1.1–1.6 kg steam per kg of water evaporated, and typical evaporation capacities of about 10–80 kg water per hour per square metre of drum surface under ideal conditions. Applied to this example, that implies roughly 376–547 kg/h of steam and anywhere from about 4 to 34 m² of drum surface. The spread of that area range shows why a vendor cannot size either machine from a datasheet. It depends on the film and the product, and only a trial narrows it.

This is thermal energy. Electrical energy for drum drive, rotor drive, vacuum pumps, condensers, fans and milling is separate and should be quoted separately. See our energy audit guide and our guide to heat source selection.

Choosing between them: a practical sequence

  1. Define the feed. Solids content, viscosity at feed temperature, stickiness, and whether it forms a film or a crust when heated.
  2. Define the product. Flakes that are milled afterwards, or powder or granules directly. Check bulk density, solubility and particle size requirements.
  3. Define thermal limits. Heat-sensitive products may need a vacuum drum or a low-temperature ATFD. Our guide to low-temperature drying covers the alternatives.
  4. Define containment. If vapours must be condensed, odour contained or solvent recovered, an enclosed machine is attractive.
  5. Run trials on both if the feed is borderline. GTI’s pages describe pilot testing; our pilot plant guide explains what to request.

For sticky filter cakes, pastes and sludges more broadly, see our guide to the best dryer for sticky filter cakes and pastes and our ETP sludge dryer guide. If the feed is a very wet sludge, a mechanical dewatering step first can change the thermal load substantially.

Common risks to check at quotation

  • Overheating at the wall. Check wall temperature and the product’s thermal limit.
  • Burn-on and film breaks. Ask how the supplier handles feed variation.
  • Downstream milling and dust. Drum flakes often need a mill. Dusts are combustible, see our dust explosion prevention guide.
  • Wear parts. Doctor blades, applicator rolls, rotor blades and seals are consumables.
  • Cleaning and changeover. Ask about cleaning access and CIP provisions.
  • Materials of construction. Match the metallurgy to the feed’s chemistry.

Browse the full dryer range from the GTI homepage.

Frequently asked questions

Is a drum dryer or a thin-film dryer better for pastes?

Both can dry pastes. A drum dryer is the long-established choice for pastes and gelatinised starch wanted as flakes. An ATFD suits fouling-prone, heat-sensitive feeds and yields powder directly. Trials decide.

Can a spray dryer replace a drum dryer?

Only if the feed can be pumped and atomised. Very viscous pastes that clog nozzles are usually unsuitable for spray drying.

What moisture can these dryers reach?

The TNO review reports final moisture below 5% wet basis for drum drying and a dry powder product from ATFD, but the achievable value depends on the product and conditions.

What does a drum dryer need besides steam?

Electrical power for drive and fans, a vapour hood and extraction, milling for flakes if powder is required, and a feed system that holds the film steady.

How do I size either dryer?

Calculate the evaporation load from feed and product moisture, then confirm the area or volume through trials. Datasheet ratings are not enough.

Discuss your paste or slurry with GTI

For assistance with dryer selection, processing requirements or a project-specific quotation for a drum or thin-film drying system, contact Genex Tech Industries LLP (GTI Group).

Email: mktg@gtidryers.com
Call or WhatsApp: +91-93300 77417
Website: https://gtidryers.com/

Please share your material, required wet-feed capacity, initial and target moisture, available heating source and installation location.

Chat on WhatsApp