Skip to main content

GTI Industrial Dryers

Short answer: Most extruded floating and sinking fish feed is dried on a continuous multi-zone belt (conveyor) dryer, followed by a cooler and, where needed, a fat coater. Fluid bed and vibratory fluid bed dryers suit small, uniform pellets and crumbles that fluidise well. Heat pump drying is a niche choice for low-temperature specialty formulations, not a default for high-tonnage aquafeed. The deciding factors are pellet size range, required throughput, how sensitive pellet durability and expansion are to drying conditions, and how evenly the dryer brings every pellet below the moisture and water-activity limit.

This guide helps aquafeed plant owners, feed technologists and project engineers pick a dryer type and write an enquiry that suppliers can quote on like-for-like terms.

What the dryer has to achieve

Extruded aquafeed leaves the die hot and wet. In his doctoral thesis on hot-air drying of extruded fish feed, Anders Haubjerg reports typical extruder discharge moisture of 22–27% (wet basis). Some moisture flashes off during transfer to the dryer, typically 2–3 percentage points. The dryer then brings the pellets to about 8–10%.

Galen Rokey’s review of feed extrusion technology gives the microbiological reasoning. Dry extruded products generally need less than 10% moisture. Water activity below 0.65 prevents bacterial problems, and below 0.60 helps prevent mould. GTI’s fish feed drying systems page cites a safe level of roughly 10–12% depending on the product.

The correct target for your feed is the moisture at which your formulation reaches the required water activity. Measure it rather than assuming it, because fat, salt and ingredient mix shift the relationship.

The dryer is also where physical quality is set. Haubjerg found that drying temperature, humidity and air velocity all affect pellet mechanical durability, with interacting effects. He also recommends avoiding high temperature at the onset of the glass transition, because it can increase hardness. Drying removes water from the pores created in extrusion, and those pores later take up oil in the coater. Over-drying, under-drying and uneven drying therefore all show up downstream.

The main dryer options

Dryer typeHow it worksBest suited toMain limitations
Multi-zone belt (conveyor) dryerPellets travel as a bed on a perforated or mesh belt. Hot air passes through the bed in several zones; single- or multi-pass layouts are usedMost extruded floating and sinking feeds; wide pellet size ranges; high continuous throughputBed depth and airflow distribution must be uniform, otherwise moisture varies across the belt; belt cleaning between recipes
Fluid bed / vibratory fluid bed dryerAir fluidises the pellets; vibration helps transport and evens out residence timeSmall, uniform pellets, crumbles and granules; also cooling dutyLarge or fragile pellets may abrade and create fines; air volume depends on pellet size and density; less flexible for big size changes
Heat pump dryerClosed or partly closed air loop dehumidified by a heat pump, at lower temperaturesLow-temperature specialty or hatchery feeds and small batches where temperature limits matterLower drying rate at low temperature; capacity and capital cost must be compared carefully for bulk production

GTI’s fish feed page lists mesh belt dryers, fluidised bed and vibratory fluidised bed dryers, and heat pump dryers as the technologies it applies to aquafeed. Which one fits a given plant is an engineering question. The following sections show how to answer it.

Worked example: separating wet feed, product and evaporation

Illustrative assumptions: extruder output 5,000 kg/h at 25% moisture (wet basis). Flash-off during transfer reduces this to 23% before the dryer. Target dryer discharge is 9%.

ItemCalculationResult
Dry solids5,000 × (1 − 0.25)3,750 kg/h
Wet feed entering dryer3,750 ÷ (1 − 0.23)4,870 kg/h
Water flashed before dryer5,000 − 4,870130 kg/h
Dried product leaving dryer3,750 ÷ (1 − 0.09)4,121 kg/h
Evaporation in dryer4,870 − 4,121749 kg/h
Dry-basis moisture in / out0.23 ÷ 0.77 and 0.09 ÷ 0.910.299 → 0.099 kg/kg

In practice the cooler often removes a little more moisture. That should be included in the overall balance rather than assumed away.

Three points follow:

  • A supplier quoting “5 t/h dryer” may mean extruder output, dryer inlet or product. Ask for all three, plus evaporation in kg/h.
  • The minimum latent heat for 749 kg/h of evaporation is roughly 749 × 2,358 kJ/kg ≈ 1.77 GJ/h (about 0.49 MW) at around 60 °C. Real convective dryers need more for air heating, exhaust losses and casing losses. Ask for the full heat balance and the exhaust conditions it assumes.
  • Electrical power for fans, belt drives and conveyors is a separate figure (kW). Keep it apart from thermal demand when you compare offers.

Selection criteria that actually decide the choice

1. Pellet size range and recipe changes

A plant producing 1–2 mm starter feed and 6–8 mm grower feed on the same line needs a dryer that handles both without big swings in air velocity or bed behaviour. Belt dryers adjust through belt speed, bed depth and zone temperatures. Fluid beds are sensitive to particle size and density, because the fluidising velocity has to suit the pellet.

2. Moisture uniformity

Uneven airflow is a known cause of moisture variation in feed belt dryers. A CFD study of a single-belt feed dryer published in Energy Procedia found that feed bed thickness significantly changed the airflow velocity distribution. If some pellets leave at 12% and others at 7%, operators usually overdry the whole batch to protect the wettest fraction. Ask suppliers how they distribute air across the belt width and how they spread the feed evenly. Our guide to uneven moisture in belt dryers covers diagnosis in detail.

3. Drying conditions and pellet quality

For a horizontal conveyor dryer, Rokey quotes air velocities of 40–60 m/min through the bed and air temperatures of 90–180 °C. Where your recipe sits within such ranges should be decided with trials, because durability, expansion and colour respond to temperature, humidity and residence time together. Heat-sensitive additives such as vitamins and probiotics are usually applied after drying, in the coater, rather than exposed to dryer temperatures. Confirm this with your formulation team.

4. Equilibrium moisture and storage climate

Research on drying curves and sorption isotherms of extruded fish feed showed that the feed’s equilibrium moisture rises sharply above about 0.6 water activity. The authors advise care in handling where air relative humidity is above 60%. In humid coastal regions, the cooler and storage design, including air intake conditions, matter as much as the dryer.

5. Heating source and utilities

Belt and fluid bed dryers can be heated by steam coils, thermic fluid, or hot-air generators burning gas or biomass. The right choice depends on what the plant already has. If the extruder preconditioner already uses steam, a steam-coil dryer may simplify utilities. A plant without a boiler may prefer a hot-air generator. Indirect heating keeps combustion products away from the feed.

6. Hygiene, fines and fire safety

Fines and fat collect in dryer plenums and on belts. Specify access doors, cleanable plenums and a cleaning routine. Fat-laden dust in a hot dryer is a fire risk, so include temperature monitoring and, where justified, fire detection and suppression.

Where DDGS and new ingredients come in

Indian feed makers are increasingly including distillers dried grains with solubles (DDGS) in aquafeed. Mint reported in November 2026 that aquaculture producers are substituting 15–25% of soy protein with rice- or corn-based DDGS. Changes in fibre, fat and protein can alter expansion, pellet density and drying behaviour. When a reformulation is significant, re-check dryer settings and pellet durability rather than assuming the previous conditions still apply. For more on the ingredient itself, see our article on DDGS drying in India’s grain ethanol plants.

Buyer checklist for an aquafeed dryer enquiry

  1. Extruder output (kg/h) for each product, and pellet sizes (mm), including the smallest and largest.
  2. Moisture at extruder discharge and target moisture after dryer and after cooler, both on a wet basis.
  3. Target water activity, if specified.
  4. Bulk density and any floating or sinking requirement.
  5. Recipe change frequency and acceptable changeover time.
  6. Heating medium available and its capacity.
  7. Site ambient temperature and humidity range.
  8. Downstream equipment: cooler, coater, screening.
  9. Cleaning, fines handling and fire protection expectations.
  10. Electrical load, listed separately from thermal duty.

For upstream grinding of feed ingredients before extrusion, GTI Group’s hammer mill grinding systems are described on foodtechprojects.com. Particle size from grinding affects extrusion and, indirectly, drying.

Frequently asked questions

What moisture should extruded fish feed be dried to?

Published sources commonly give about 8–10% after drying, or less than 10%. The real criterion is water activity: below about 0.65 for bacteria and 0.60 for mould, according to Rokey. Verify the moisture that achieves this for your recipe.

Can one dryer handle both shrimp and fish feed?

Often yes, if it is designed for the full pellet size and density range. Shrimp feed is usually small, dense, sinking pellets. Fish feed may be large and floating. Give suppliers both specifications.

Is a vertical counterflow cooler enough to finish drying?

A cooler removes some moisture, but its main job is cooling. Relying on it to finish drying makes final moisture depend on ambient conditions.

Do I need a pilot trial?

For a new formulation, unusual pellet size or high ingredient change, yes. Trials confirm drying time, durability and moisture uniformity. Read more on pilot testing for industrial dryers.

Talk to GTI about your aquafeed drying line

For help selecting a fish or shrimp feed dryer, sizing a drying and cooling line, or a project-specific quotation, contact Genex Tech Industries LLP (GTI Group).

Email: mktg@gtidryers.com
Call or WhatsApp: +91-93300 77417
Website: https://gtidryers.com/

Please share your material, required wet-feed capacity, initial and target moisture, available heating source and installation location.

Chat on WhatsApp